> instance could be replaced somehow, but I’d rather not sieve > * if *printf/sprintf supported* by SDCC/STM8? Of course each However AFAIK the RAM data bus is just 8 bits wide, so you'd get even
Stm8 cosmic .bss size overflow code#
Pipeline stalls once in a while, which slow your code down a bit > operations have to be executed from RAM (or so I think).Īccording to my understanding of the stm8 architecture you should beĪble to have both code and your data in flash (resulting in a few > to flash, but since the flash is single-ported, the actual flash > * how can I write *code to execute from RAM*? I need to log data Though: sdcc emits a warning for doubles and replaces them by floats. The stm8 port passes the regression tests, > seems so, but I always get an error message when I try an operationįloat is supported. > handy, independent of speed and memory. > avoid float wherever possible, but sometimes it would come very > * does SDCC for STM8 also support *float operations*? I try to > SDCC and ST-Link (from STM8 discovery board)? If required, R-Link Is there a *debugger with GUI*, which supports
![stm8 cosmic .bss size overflow stm8 cosmic .bss size overflow](https://i.stack.imgur.com/iFazd.png)
> * since I’m into physical computing, debugging via simulator is not Shuld be English instructions in the download). Someone did some work for Code::Blocks, but I didn't try it > or configurable for SDCC/STM8? Ideally with compiling, linking, > but feels solo 80s... -) Is there any *IDE with built-in support* > * currently I use SDCC via an ASCII editor and a console. For your support thanks a lot in advance!!! :-) So, I hope they are simple, and that someone will > after evaluating SDCC for STM8 for a few weeks now, I still have Iob/WwM8B/gxsevfg54FDZFxmiuh6hpdJsqpKC7qPVLYA9R5oO6AJf8icrpGyeMnĢK3hKN1DvFom4GJt0nohXVFLaHKUPfms8ufOEcXIcj6JHqK5OohGCRScsNPMEu0= IQEcBAEBAgAGBQJTOR8+AAoJEJFP1HbJm5DndocIAIA+zmYulHeYClYNUN8z4Js0ĨGE0eTGe8s+bSwB99+yKp3aXH5BOg4SIlrJT08ZNn3SKhs3bTC6kEkNdz1A5RsmEĪVtei8IsQ5wqyQtVfQtski3wqz+xhJ3T2XMIgmOj+uBSCakMJK1GNKGLZdJbq2c4ġi2AbywWe32In4Q8bZNSWf6s1CseLPWprzu4oU3/6jx/p6TihBM/fqBR5Iyec4r2 > (the post is in German, but the download should include English
![stm8 cosmic .bss size overflow stm8 cosmic .bss size overflow](https://www.electronics-lab.com/wp-content/uploads/2020/07/schem.png)
> Apparently someone made something for Code::Blocks at
Stm8 cosmic .bss size overflow software#
> software I write and the kind of debugging I need, good old printf is but I don't use debugger, would not be much any good with the kind of > I use SDCC with Eclipse (CDT) as described here: > SDCC/STM8? Ideally with compiling, linking, upload and debug (see below > Is there any *IDE with built-in support* or configurable for I have used that myself a few times with the PIC16 tols. The built-in option list may be a little outdated, but you can still add any Yes, SDCC can be integrated with code blocks.